Internet sharing xbox live windows 7

So I knew how to bridge devices, but didn't think of that. I had this too, eventually found I had to enable it via the command prompt. If anyone has this issue, first uncheck the sharing you enabled in the first three steps and restart your pc otherwise this option still won't appear.

I also had an entry just called 'wifi' - don't use this one, didn't work for me. It's actually pretty quick and easy once you've done it once. You may have to reenable if you reboot your pc. NOTE: I was setting up a pc which had an Ethernet internet access connection, then using its wifi for the new shared connection. Not all wifi cards are suitable for the above, apparently.

This thread is locked. You can follow the question or vote as helpful, but you cannot reply to this thread. I have the same question Report abuse. Details required :. Cancel Submit. Previous Next. User Moderator. Right-click the network adapter with an Internet connection Ethernet or wireless network adapter , then select Properties. Click Sharing.

Click OK to finish. Let us know how it goes. How satisfied are you with this reply? Thanks for your feedback, it helps us improve the site. In reply to A. User's post on December 7, As I remember, you had to assign the second adapter a static IP address? User Microsoft Agent. In reply to KenoshaKicker's post on February 3, Hi Kenosha, For more details about enabling Internet Connection Sharing on Windows 10, we recommend checking out this page.

Let us know if you have additional questions. User's post on February 4, This page does not lead to anything useful for Windows Check the box for each service that you want to enable. Open your wireless router's configuration page. Now that the host computer is set up, you'll need to configure the router to allow it to pass the connection through.

Click here for detailed instructions on opening the router's configuration page. If you're using a hub or switch, you won't need to perform any additional configuration. Open the Internet Settings page on the router.

The exact wording will vary from model to model. Again, the wording will vary slightly depending on your exact router. Connect your other computers and devices to the router or hub. Your host and router have been configured, and now it's time to connect your other devices.

If connecting via Ethernet, connect each additional computer to the LAN ports on the router or hub. If connecting wirelessly, connect to the router as if you were connecting to any wireless network. There is no.

This is typically the case if you only have one network adapter installed. You must have at least two different network adapters installed to use internet connection sharing.

The other computers on the network are not getting an internet connection. This is typically caused by the computer not getting a correct IP address.

Make sure that you only have internet connection sharing enabled on the host computer, and only on the adapter that's connected to the internet. All of the other computers on the network should not have internet connection sharing enabled.

Open the Network Connections window on the computer that cannot get an internet connection. Right-click on the network adapter and select Properties. Select "Obtain IP address automatically".

The other computers can share files but cannot connect to the internet. Bridging your two network adapters may help solve this problem. Select the two adapters that you want to bridge. This should be the adapter that is connected to the internet and the adapter that is connected to the rest of the network.

Hold Ctrl and click each one to select them. Right-click on one of the two selected networks and select "Bridge Connections". Click Yes when prompted. Reboot the other computer and try connecting again. I'm receiving the "An error occurred while Internet Connection Sharing was being enabled. This can be caused by a problem with the internet sharing services in Windows. Press Enter to open the Services window. Reboot the computer after setting each service and try the connection again.

Method 2. Follow the steps in the first section to enable internet connection sharing on the host computer. This method will allow you to use an unused wireless adapter on your Windows host computer to broadcast a wireless network that any other device can connect to, just like a wireless router. First, you'll need to enable internet connection sharing on the host computer by following Steps of the first section.

The host computer will need to have a wireless adapter that isn't being used in order to broadcast a signal for other computers and devices to connect to.

If the host computer doesn't have a wireless card installed, you can use a USB wireless adapter. Make sure you only enable internet connection sharing on the adapter that's connected to the internet. Don't enable internet sharing on the wireless adapter that you'll be using to create the wireless network.

This will open a new window with your active network connections. Select "Set up a new connection or network". This link can be found towards the bottom of the Network and Sharing Center window. Select "Set up a wireless ad hoc computer-to-computer network". If you are using Windows 8, you will need to download a free program like Virtual Router virtualrouter. Make sure that the Security Key cannot be easily guessed. Make sure to check the "Save this network" box, or you'll need to reconfigure it every time you reboot the computer.

Connect your other computers and devices to the new wireless network. With the wireless network created and internet connection sharing enabled, you should now be able to connect any of your other computers or mobile devices to the wireless network just like any other wireless network.

Enter in the Security Key you created in the previous step to connect. My device won't connect to the wireless network. Some older devices cannot properly connect to an ad-hoc network, and the problem can get even worse if they don't support WPA If you absolutely have to have that device on the network, try lowering the ad-hoc network's security to WEP.

Method 3. Understand the ways you can share your connection. OS X's Sharing menu allows you to easily share your Mac's internet connection using any of your installed network adapters. The computer sharing the network is called the "host" computer. You will need at least two network adapters installed in the host to share your connection; one to connect to the internet, and one to connect to the rest of your network. If you have an unused wireless adapter for example, your host is connected to the modem via Ethernet , you can use it to create a wireless network that other devices can connect to in order to access the internet.

If you have two Ethernet adapters, you can connect one to the modem, and the other to a network switch or router. Your other computers and devices can then connect to this network. Connect the host computer directly to the internet source. For the best results, it's recommended that you connect the host computer directly to your broadband modem via Ethernet, or use a USB hotspot. Open the System Preferences menu on the host Mac computer. Click the Apple menu and select "System Preferences".

Click the "Sharing" option. This will open the Sharing window. Check the "Internet Sharing" box in the left frame. This will enable sharing for the host computer's internet connection. Click the "Share your connection from" menu and select your internet source. If you're connected to your modem via Ethernet, select it from the menu. If you're connected to a USB hotspot, select it instead.

Click Start to confirm that you want to enable internet sharing. Note that turning internet connection sharing on will likely disrupt any existing network you have set up. Select the method that you want to broadcast your connection. The method you choose depends on the way you want other computers to connect. If you want to turn your Mac into a wireless hotspot, check the "Wi-Fi" box. If you want to connect your Mac to a network hub or wireless router, select "Ethernet".

Connect the host mac to the network hub or router's WAN port Ethernet. If you opted to share your host's internet connection with a hub or router which the other computers will connect to, use an Ethernet cable and connect your host to the hub's WAN port. Configure your wireless settings Wi-Fi. If you decided to turn your Mac into a wireless access point, click the Wi-Fi Options Make sure to select "WPA2 Personal" as the "Security" type, and create a password that won't be easily guessed.

Doing so will help reduce interference. Your host Mac is now ready to share its internet connection, and you can connect the other computers and devices as if it was a typical network.

They should automatically get IP addressed and be able to connect to the internet. My other devices are not able to get an internet connection. This will often occur if you've made changes to the sharing settings after enabling the wireless network.

The quickest way to try to fix this problem is by disabling Internet Sharing, restarting the Mac, and then re-enabling it and creating a new wireless network.